Manuals

Manuals
Specifications: Dell 2001FP Flat Panel Color Monitor User's Guide

Back to Contents Page

Specifications: Dell™ 2001FP Flat Panel Color Monitor User's Guide

General Flat Panel Resolution Preset Display Modes Electrical Physical Characteristics Environmental Power Management Modes Pin Assignments Universal Serial Bus (USB) Interface Plug and Play Capability


General

Model number 2001FP

Flat Panel

Screen type Active matrix - TFT LCD
Screen dimensions 20.1 inches (20.1-inch viewable image size)
Preset display area:
Horizontal
408 mm (16.1 inches)
Vertical
306 mm (12.1 inches)
Pixel pitch 0.255 mm
Viewing angle +/- 88° (vertical) typ, +/- 88° (horizontal) typ
Luminance output 250 cd/m ²(typ)
Contrast ratio 400:1
Faceplate coating Antiglare with hard-coating 3H
Backlight CCFL (6) edgelight system
Response Time 16ms typical

Resolution

Horizontal scan range 31 kHz to 80 kHz (automatic)
Vertical scan range 56 Hz to 76 Hz, exception 1600 x 1200 at 60 Hz only
Optimal preset resolution 1600 x 1200 at 60 Hz
Highest preset resolution 1600 x 1200 at 60 Hz

Dell guarantees image size and centering for all preset modes listed in the following table.


Preset Display Modes

Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (Horizontal/Vertical)
IBM?/sup>, VGA1, 720 x 400 31.5 70.1 28.3 -/+
IBM, VGA3, 640 x 480 31.5 59.9 25.2 -/-
VESA?/sup>, 640 x 480 37.5 75.0 31.5 -/-
VESA, 800 x 600 37.9 60.3 40.0 +/+
VESA, 800 x 600 46.9 75.0 49.5 +/+
VESA, 1024 x 768 48.4 60.0 65.0 -/-
VESA, 1024 x 768 60.0 75.0 78.8 +/+
VESA, 1152 x 864 67.5 75.0 108.0 +/+
VESA, 1280 x 1024 64.0 60.0 108.0 +/+
VESA, 1280 x 1024 80.0 75.0 135.0 +/+
VESA, 1600 x 1200 75.0 60.0 162.0 +/+

Electrical

Video input signals

Analog RGB, 0.7 Volts +/-5%, 75 ohm input impedance 

Digital DVI-D TMDS, 600mV for each differential line, 50 ohm input impedance

S-video, Y input 1 volt(p-p), C input 0.286 volt(p-p), 75 ohm input impedance

Composite, 1 volt(p-p), 75 ohm input impedance

Synchronization input signals separate horizontal and vertical;
3.3V Cmos or 5V TTL level, positive or negative sync.
AC input voltage / frequency / current 90 to 264 VAC / 50 or 60 Hz + 3 Hz / 2.0A (Max.)
Inrush current 110V: 60A (Max.)
220V: 120A (Max.)

Physical Characteristics

Connector type  
Signal cable type

D-sub: Detachable, Analog, 15pin, shipped attached to the monitor
DVI-D: Detachable, Digital, 24pin, shipped detached from the monitor                                      S-video: Not included with display                                                                                  Composite: Not included with display

Dimensions (with stand):
Height (fully extended in portrait mode)
635.0 mm (25 inches)
Height (compressed/locked in landscape mode)
457.7 mm (18 inches)
Width
447 mm (17.6 inches)
Depth
245.5 mm (9.67 inches)
Weight 
Monitor (Stand and Head) 8.5 Kg (18.72 lb)
Power Supply Brick 0.47Kg (1.03 lb)
Monitor Flat panel only (VESA Mode) 5.45Kg (12.0 lb)
Weight with packaging 11.2Kg (24.63 lb)

Environmental

Temperature:
Operating
5° to 35°C (41° to 95°F)
Nonoperating
Storage: 0° to 60°C (32° to 140°F)
Shipping: -20° to 60°C(-4° to 140°F)
Humidity:
Operating
10% to 80% (noncondensing)
Nonoperating
Storage: 5% to 90% (noncondensing)
Shipping: 5% to 90%(noncondensing)
Altitude:
Operating
3,657.6m (12,000 ft) max
Nonoperating
12,192 m (40,000 ft) max
Thermal dissipation 238.84 BTU/hour (maximum)
187.66 BTU/hour (typical)

Power Management Modes

If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. This is referred to as 'Power Save Mode'*. If input from keyboard, mouse or other input devices is detected by the computer, the monitor will automatically "wake up". The following table shows the power consumption and signaling of this automatic power saving feature:

VESA Modes Horizontal Sync Vertical Sync Video Power Indicator Power Consumption
Normal operation Active Active Active Green 90 W (max. with USB and Soundbar)
Active-off mode Inactive Inactive Blanked Amber Less than 3 W Avg.
Switch off
-
-
-
Off Less than 1 W

Note: The OSD will only function in the 'normal operation' mode. Otherwise one of the following messages will appear depending upon the selected input.

1. Analog Input

In Power Save Mode

Press Any Key on Keyboard or Move Mouse

  or  

2. Digital Input

In Power Save Mode

Press Any Key on Keyboard or Move Mouse

Activate the computer and 'wake up' the monitor to gain access to the OSD.

3. S-video Input

In Power Save Mode

               Please Check Video Signal            

  or  

4. Composite Input

In Power Save Mode

               Please Check Video Signal            

Check the video signal and 'wake up' the monitor to gain access to the OSD.

This monitor is ENERGY STAR®-compliant as well as TCO '99/ TCO '03 power management compatible.

* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.

ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, DELL has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.


Pin Assignments

15-pin D-sub Connector


Pin Number

15-Pin Side of the Signal Cable
1 Video-Red
2 Video-Green
3 Video-Blue
4 GND
5 Self-test
6 GND-R
7 GND-G
8 GND-B
9 PC5V
10 GND-sync
11 GND
12 DDC data
13 H-sync
14 V-sync
15 DDC clock

 

24 Pin Digital DVI-D Connector:

 


Pin Number

24-Pin Side of the Signal Cable
1 TMDS RX2-
2 TMDS RX2+
3 TMDS Ground
4 Floating
5 Floating
6 DDC Clock
7 DDC Data
8 Floating
9 TMDS RX1-
10 TMDS RX1+
11 TMDS Ground
12 Floating
13 Floating
14 +5V Power
15 Self test 
16 Hot Plug Detect
17 TMDS RX0-
18 TMDS RX0+
19 TMDS Ground
20 Floating
21 Floating
22 TMDS Ground
23 TMDS Clock+
24 TMDS Clock-

 


S-video connector


Pin Number

5-Pin Side of the Signal Cable
1 GND
2 GND
3 LUMA
4 CHROMA
5 GND

Composite Connector

Pin Number 1-Pin Side of the Signal Cable
1 LUMA COMPOSITE CHROMA

 

Universal Serial Bus (USB) Interface

 

This monitor supports High-Speed Certified USB 2.0 interface.*

 Data Rate Power Consumption
High speed 480 Mbps 2.5W (Max., each port)
Full speed 12 Mbps 2.5W (Max., each port)
Low speed 1.5 Mbps 2.5W (Max., each port)

 

USB Upstream connector

 

Pin Number

4-Pin Side of the Signal Cable
1 VCC
2 DMU
3 DPU
4 GND

 

USB Downstream connector

 

Pin Number

4-Pin Side of the Signal Cable
1 VCC
2 DMD
3 DPD
4 GND

 

 

USB ports:

  • 1 upstream - rear
  • 4 downstream - 2 on rear; 2 on left side

*Note: USB 2.0 capability requires 2.0 capable computer 

Note: *Monitor's USB interface works ONLY when monitor is Powered ON (or in Power Save Mode). Switching your monitor OFF and then ON would re-enumerate its USB interface; attached peripherals may take a few seconds to resume normal functionality.


Plug and Play Capability

You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. If desired, the user can select different settings, but in most cases monitor installation is automatic.


Back to Contents Page

snWEB7